79 lines
3.6 KiB
Django/Jinja
79 lines
3.6 KiB
Django/Jinja
# {{ ansible_managed }}
|
|
#
|
|
# This is the configuration file for ser2net. It has the following format:
|
|
# <TCP port>:<state>:<timeout>:<device>:<options>
|
|
# TCP port
|
|
# Name or number of the TCP/IP port to accept con-
|
|
# nections from for this device. A port number may
|
|
# be of the form [host,]port, such as 127.0.0.1,2000
|
|
# or localhost,2000. If this is specified, it will
|
|
# only bind to the IP address specified. Otherwise
|
|
# it will bind to all the ports on the machine.
|
|
#
|
|
# state Either raw or rawlp or telnet or off. off disables
|
|
# the port from accepting connections. It can be
|
|
# turned on later from the control port. raw enables
|
|
# the port and transfers all data as-is between the
|
|
# port and the long. rawlp enables the port and
|
|
# transfers all input data to device, device is open
|
|
# without any termios setting. It allow to use
|
|
# /dev/lpX devices and printers connected to them.
|
|
# telnet enables the port and runs the telnet proto-
|
|
# col on the port to set up telnet parameters. This
|
|
# is most useful for using telnet.
|
|
#
|
|
# timeout
|
|
# The time (in seconds) before the port will be dis-
|
|
# connected if there is no activity on it. A zero
|
|
# value disables this funciton.
|
|
#
|
|
# device The name of the device to connect to. This
|
|
# must be in the form of /dev/<device>.
|
|
#
|
|
# options
|
|
# Sets operational parameters for the serial port.
|
|
# Options 300, 1200, 2400, 4800, 9600, 19200, 38400,
|
|
# 57600, 115200 set the various baud rates. EVEN,
|
|
# ODD, NONE set the parity. 1STOPBIT, 2STOPBITS set
|
|
# the number of stop bits. 7DATABITS, 8DATABITS set
|
|
# the number of data bits. [-]XONXOFF turns on (-
|
|
# off) XON/XOFF support. [-]RTSCTS turns on (- off)
|
|
# hardware flow control, [-] LOCAL turns off (- on)
|
|
# monitoring of the modem lines, and
|
|
# [-]HANGUP_WHEN_DONE turns on (- off) lowering the
|
|
# modem control lines when the connextion is done.
|
|
# NOBREAK disables automatic setting of the break
|
|
# setting of the serial port.
|
|
# The "remctl" option allow remote control (ala RFC
|
|
# 2217) of serial-port configuration. A banner name
|
|
# may also be specified, that banner will be printed
|
|
# for the line. If no banner is given, then no
|
|
# banner is printed.
|
|
#
|
|
# or...
|
|
|
|
# BANNER:<banner name>:banner
|
|
# This will create a banner, if the banner name is given in the
|
|
# options of a line, that banner will be printed. This takes the
|
|
# standard "C" \x characters (\r is carraige return, \n is newline,
|
|
# etc.). It also accepts \d, which prints the device name, \p,
|
|
# which prints the TCP port number, and \s which prints the serial
|
|
# parameters (eg 9600N81). Banners can span lines if the last
|
|
# character on a line is '\'. Note that you *must* use \r\n to
|
|
# start a new line.
|
|
#
|
|
# Note that the same device can be listed multiple times under different
|
|
# ports, this allows the same serial port to have both telnet and raw
|
|
# protocols.
|
|
|
|
# The original config file shipped with the upstream sources can be
|
|
# found in /usr/share/doc/ser2net/examples
|
|
|
|
{% hass_ser2net_zwave %}
|
|
{{ hass_ser2net_port_zwave}}:raw:0:/dev/zwave0:115200 8DATABITS NONE NOBREAK LOCAL 1STOPBIT
|
|
{% endif %}
|
|
|
|
{% if hass_ser2net_zigbee %}
|
|
{{ hass_ser2net_port_zigbee}}:raw:0:/dev/zigbee0:115200 8DATABITS NONE NOBREAK LOCAL 1STOPBIT
|
|
{% endif %}
|