76 lines
2.6 KiB
ReStructuredText
76 lines
2.6 KiB
ReStructuredText
Belling BL0940 Energy Monitor
|
|
=============================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up BL0940 power monitors.
|
|
:image: bl0940.png
|
|
:keywords: BL0940
|
|
|
|
.. note::
|
|
|
|
This page is incomplete and could some work. If you want to contribute, please read the
|
|
:doc:`contributing guide </guides/contributing>`. This page is missing:
|
|
|
|
- Images/screenshots/example configs of this device being used in action.
|
|
|
|
The ``bl0940`` sensor platform allows you to use BL0940 energy monitors sensors with
|
|
ESPHome. These are used in some Tuya-devices (e.g. the power metering BW-SHP10)
|
|
|
|
The communication with this component is done via a :ref:`UART <uart>`.
|
|
You must therefore have a ``uart:`` entry in your configuration with both the TX and RX pins set
|
|
to some pins on your board and the baud rate set to 4800 with 1 stop bit.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
id: uart_bus
|
|
tx_pin: TX
|
|
rx_pin: RX
|
|
baud_rate: 4800
|
|
stop_bits: 1
|
|
|
|
sensor:
|
|
- platform: bl0940
|
|
uart_id: uart_bus
|
|
voltage:
|
|
name: 'BL0940 Voltage'
|
|
current:
|
|
name: 'BL0940 Current'
|
|
power:
|
|
name: 'BL0940 Power'
|
|
energy:
|
|
name: 'BL0940 Energy'
|
|
internal_temperature:
|
|
name: 'BL0940 Internal temperature'
|
|
external_temperature:
|
|
name: 'BL0940 External temperature'
|
|
update_interval: 60s
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **voltage** (*Optional*): The voltage value of the sensor in Volts.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **current** (*Optional*): The current value of the sensor in Amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **power** (*Optional*): The (active) power value of the sensor in Watts. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **energy** (*Optional*): Use the voltage value of the sensor in kWh.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **internal_temperature** (*Optional*): The internal temperature value of the sensor in °C.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **external_temperature** (*Optional*): The external value of the sensor in °C. Often not connected and gives garbage data.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
|
|
sensor. Defaults to ``60s``.
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :apiref:`bl0940/bl0940.h`
|
|
- :ghedit:`Edit`
|