87 lines
3.0 KiB
ReStructuredText
87 lines
3.0 KiB
ReStructuredText
INA3221 3-Channel DC Current Sensor
|
|
===================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up INA3221 3-channel DC current sensors.
|
|
:image: ina3221.jpg
|
|
:keywords: ina3221
|
|
|
|
The ``ina3221`` sensor platform allows you to use your INA3221 3-Channel DC Current Sensor
|
|
(`datasheet <http://www.ti.com/lit/ds/symlink/ina3221.pdf>`__,
|
|
`switchdoc`_) sensors with
|
|
ESPHome. The :ref:`I²C Bus <i2c>` is
|
|
required to be set up in your configuration for this sensor to work.
|
|
|
|
|
|
.. figure:: images/ina3221-full.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
INA3221 3-Channel DC Current Sensor
|
|
|
|
.. _switchdoc: http://www.switchdoc.com/ina3221-breakout-board/
|
|
|
|
.. figure:: images/ina3221-ui.png
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
sensor:
|
|
- platform: ina3221
|
|
address: 0x40
|
|
channel_1:
|
|
shunt_resistance: 0.1 ohm
|
|
current:
|
|
name: "INA3221 Channel 1 Current"
|
|
power:
|
|
name: "INA3221 Channel 1 Power"
|
|
bus_voltage:
|
|
name: "INA3221 Channel 1 Bus Voltage"
|
|
shunt_voltage:
|
|
name: "INA3221 Channel 1 Shunt Voltage"
|
|
channel_2:
|
|
# ...
|
|
channel_3:
|
|
# ...
|
|
update_interval: 60s
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **address** (*Optional*, int): Manually specify the I²C address of the sensor. Defaults to ``0x40``.
|
|
- **channel_1** (*Optional*): The configuration options for the 1st channel.
|
|
|
|
- **shunt_resistance** (*Optional*, float): The value of the shunt resistor on this channel for current calculation.
|
|
Defaults to ``0.1 ohm``.
|
|
- **current** (*Optional*): Use the current value on this channel in amperes. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **power** (*Optional*): Use the power value on this channel in watts. All options from
|
|
:ref:`Sensor <config-sensor>`.
|
|
- **bus_voltage** (*Optional*): Use the bus voltage (voltage of the high side contact) value on this channel in V.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **shunt_voltage** (*Optional*): Use the shunt voltage (voltage across the shunt resistor) value on this channel in V.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **channel_2** (*Optional*): The configuration options for the 2nd channel. Same options as 1st channel.
|
|
- **channel_3** (*Optional*): The configuration options for the 3rd channel. Same options as 1st channel.
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the sensor. Defaults to ``60s``.
|
|
|
|
|
|
.. figure:: images/ina3221-pins.jpg
|
|
:align: center
|
|
:width: 60.0%
|
|
|
|
Pins on the INA3221. For communication only VS, GND, SCL and SDA need to be connected.
|
|
Note that all 3 channels share the same GND reference.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :doc:`ina219`
|
|
- :apiref:`ina3221/ina3221.h`
|
|
- `INA3221 Arduino Library <https://github.com/switchdoclabs/SDL_Arduino_INA3221>`__ by `SwitchDoc Labs <https://github.com/switchdoclabs>`__
|
|
- :ghedit:`Edit`
|