732 lines
24 KiB
ReStructuredText
732 lines
24 KiB
ReStructuredText
LD2410 Sensor
|
|
=============
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up LD2410 sensors.
|
|
:image: ld2410.jpg
|
|
|
|
Component/Hub
|
|
-------------
|
|
.. _ld2410-component:
|
|
|
|
The ``ld2410`` sensor platform allows you to use HI-LINK LD2410 motion and presence sensors with ESPHome.
|
|
There are three variants with similar communication protocols:
|
|
|
|
- LD2410 (`datasheet and user manual <https://drive.google.com/drive/folders/1lCQv3mfHJ3XKXzweeHPFnJ_8_D_EWEKk>`__)
|
|
- LD2410B (`datasheet and user manual <https://drive.google.com/drive/folders/16zI-fium_BZeP08EyQke0rWp0BJTMvw3>`__)
|
|
- LD2410C (`datasheet and user manual <https://drive.google.com/drive/folders/1ypOlacBmmFXY6lDQ0f1hEJFmczNe-0WG>`__)
|
|
|
|
The :ref:`UART <uart>` is required to be set up in your configuration for this sensor to work, ``parity`` and ``stop_bits`` **must be** respectively ``NONE`` and ``1``.
|
|
Use of hardware UART pins is highly recommended, in order to support the out-of-the-box 256000 baud rate of the LD2410 sensor.
|
|
|
|
.. figure:: images/ld2410.jpg
|
|
:align: center
|
|
:width: 50.0%
|
|
|
|
LD2410 motion and presence sensor
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
ld2410:
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :ref:`UART Component <uart>` if you want
|
|
to use multiple UART buses.
|
|
- **throttle** (*Optional*, int): Time in milliseconds to control the rate of data updates. Defaults to ``1000ms``.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID for this :doc:`ld2410` component if you need multiple components.
|
|
|
|
Binary Sensor
|
|
-------------
|
|
|
|
The ``ld2410`` binary sensor allows you to use your :doc:`ld2410` to perform different
|
|
measurements.
|
|
|
|
.. code-block:: yaml
|
|
|
|
binary_sensor:
|
|
- platform: ld2410
|
|
has_target:
|
|
name: Presence
|
|
has_moving_target:
|
|
name: Moving Target
|
|
has_still_target:
|
|
name: Still Target
|
|
out_pin_presence_status:
|
|
name: out pin presence status
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **has_target** (*Optional*): If true target detect either still or in movement.
|
|
All options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
- **has_moving_target** (*Optional*): If true a moving target is detected.
|
|
All options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
- **has_still_target** (*Optional*): If true a still target is detected.
|
|
All options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
- **out_pin_presence_status** (*Optional*): When in :ref:`engineering mode<ld2410-engineering-mode>`, indicates whether the OUT pin indicates presence or not, otherwise ``false``.
|
|
OUT pin indication depends on the :ref:`light function<ld2410-light-function>` configuration. Might need latest firmware to work.
|
|
All options from :ref:`Binary Sensor <config-binary_sensor>`.
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
Sensor
|
|
------
|
|
|
|
The ``ld2410`` sensor allows you to use your :doc:`ld2410` to perform different
|
|
measurements.
|
|
|
|
.. code-block:: yaml
|
|
|
|
sensor:
|
|
- platform: ld2410
|
|
light:
|
|
name: light
|
|
moving_distance:
|
|
name : Moving Distance
|
|
still_distance:
|
|
name: Still Distance
|
|
moving_energy:
|
|
name: Move Energy
|
|
still_energy:
|
|
name: Still Energy
|
|
detection_distance:
|
|
name: Detection Distance
|
|
g0:
|
|
move_energy:
|
|
name: g0 move energy
|
|
still_energy:
|
|
name: g0 still energy
|
|
g1:
|
|
move_energy:
|
|
name: g1 move energy
|
|
still_energy:
|
|
name: g1 still energy
|
|
g2:
|
|
move_energy:
|
|
name: g2 move energy
|
|
still_energy:
|
|
name: g2 still energy
|
|
g3:
|
|
move_energy:
|
|
name: g3 move energy
|
|
still_energy:
|
|
name: g3 still energy
|
|
g4:
|
|
move_energy:
|
|
name: g4 move energy
|
|
still_energy:
|
|
name: g4 still energy
|
|
g5:
|
|
move_energy:
|
|
name: g5 move energy
|
|
still_energy:
|
|
name: g5 still energy
|
|
g6:
|
|
move_energy:
|
|
name: g6 move energy
|
|
still_energy:
|
|
name: g6 still energy
|
|
g7:
|
|
move_energy:
|
|
name: g7 move energy
|
|
still_energy:
|
|
name: g7 still energy
|
|
g8:
|
|
move_energy:
|
|
name: g8 move energy
|
|
still_energy:
|
|
name: g8 still energy
|
|
|
|
.. _ld2410-sensors:
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **light** (*Optional*, int): When in :ref:`engineering mode<ld2410-engineering-mode>`, indicates the light sensitivity, otherwise ``unknown``.
|
|
Value between ``0`` and ``255`` inclusive. Though it seems that the value ``85`` is the lowest value at complete darkness.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **moving_distance** (*Optional*, int): Distance in cm of detected moving target.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **still_distance** (*Optional*, int): Distance in cm of detected still target.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **moving_energy** (*Optional*, int): Energy for moving target.
|
|
Value between ``0`` and ``100`` inclusive.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **still_energy** (*Optional*, int): Energy for still target.
|
|
Value between ``0`` and ``100`` inclusive.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **detection_distance** (*Optional*, int): Distance in cm of target.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **gX** (*Optional*): Energies for the Xth gate (X => 0 to 8).
|
|
|
|
- **move_energy** (*Optional*, int): When in :ref:`engineering mode<ld2410-engineering-mode>`, the move energy of the gate, otherwise ``unknown``.
|
|
Value between ``0`` and ``100`` inclusive.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
- **still_energy** (*Optional*, int): When in :ref:`engineering mode<ld2410-engineering-mode>`, the still energy of the gate, otherwise ``unknown``.
|
|
Value between ``0`` and ``100`` inclusive.
|
|
All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
Switch
|
|
------
|
|
|
|
The ``ld2410`` switch allows you to control your :doc:`ld2410`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
switch:
|
|
- platform: ld2410
|
|
engineering_mode:
|
|
name: "engineering mode"
|
|
bluetooth:
|
|
name: "control bluetooth"
|
|
|
|
.. _ld2410-engineering-mode:
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **engineering_mode** (*Optional*): enable/disable engineering mode. Defaults to ``false``.
|
|
Notice this requires more resources and is not recommended to be enabled when not necessary.
|
|
All options from :ref:`Switch <config-switch>`.
|
|
- **bluetooth** (*Optional*): Turn on/off the bluetooth adapter. Defaults to ``true``.
|
|
All options from :ref:`Switch <config-switch>`.
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
|
|
.. _ld2410-number:
|
|
|
|
Number
|
|
------
|
|
|
|
The ``ld2410`` number allows you to control the configuration of your :doc:`ld2410`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
number:
|
|
- platform: ld2410
|
|
timeout:
|
|
name: timeout
|
|
light_threshold:
|
|
name: light threshold
|
|
max_move_distance_gate:
|
|
name: max move distance gate
|
|
max_still_distance_gate:
|
|
name: max still distance gate
|
|
g0:
|
|
move_threshold:
|
|
name: g0 move threshold
|
|
still_threshold:
|
|
name: g0 still threshold
|
|
g1:
|
|
move_threshold:
|
|
name: g1 move threshold
|
|
still_threshold:
|
|
name: g1 still threshold
|
|
g2:
|
|
move_threshold:
|
|
name: g2 move threshold
|
|
still_threshold:
|
|
name: g2 still threshold
|
|
g3:
|
|
move_threshold:
|
|
name: g3 move threshold
|
|
still_threshold:
|
|
name: g3 still threshold
|
|
g4:
|
|
move_threshold:
|
|
name: g4 move threshold
|
|
still_threshold:
|
|
name: g4 still threshold
|
|
g5:
|
|
move_threshold:
|
|
name: g5 move threshold
|
|
still_threshold:
|
|
name: g5 still threshold
|
|
g6:
|
|
move_threshold:
|
|
name: g6 move threshold
|
|
still_threshold:
|
|
name: g6 still threshold
|
|
g7:
|
|
move_threshold:
|
|
name: g7 move threshold
|
|
still_threshold:
|
|
name: g7 still threshold
|
|
g8:
|
|
move_threshold:
|
|
name: g8 move threshold
|
|
still_threshold:
|
|
name: g8 still threshold
|
|
|
|
.. _ld2410-light-threshold:
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **timeout** (*Optional*, int): Time in seconds during which presence state will stay present
|
|
after leaving. Defaults to ``5s``
|
|
All options from :ref:`Number <config-number>`.
|
|
- **light_threshold** (*Optional*, int): Sets the light threshold for the :ref:`light function<ld2410-light-function>`.
|
|
Value between ``0`` and ``255`` inclusive. Defaults to ``128``.
|
|
All options from :ref:`Number <config-number>`.
|
|
- **max_move_distance_gate** (*Optional*, int): Maximum distance gate for movement detection.
|
|
Value between ``2`` and ``8`` inclusive. Defaults to ``8``.
|
|
All options from :ref:`Number <config-number>`.
|
|
- **max_still_distance_gate** (*Optional*, int): Maximum distance gate for still detection.
|
|
Value between ``2`` and ``8`` inclusive. Defaults to ``8``.
|
|
All options from :ref:`Number <config-number>`.
|
|
- **gX** (*Optional*): Thresholds for the Xth gate (X => 0 to 8).
|
|
|
|
- **move_threshold** (**Required**, int): Threshold for the gate for motion detection.
|
|
Above this level for the considered gate (distance), movement detection will be triggered.
|
|
Value between ``0`` and ``100`` inclusive. See default values below.
|
|
All options from :ref:`Number <config-number>`.
|
|
- **still_threshold** (**Required**, int): Threshold for the gate for still detection.
|
|
Above this level for the considered gate (distance), still detection will be triggered.
|
|
Value between ``0`` and ``100`` inclusive. See default values below.
|
|
All options from :ref:`Number <config-number>`.
|
|
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
.. list-table:: Default values for gate threshold
|
|
:widths: 25 25 25
|
|
:header-rows: 1
|
|
|
|
* - Gate
|
|
- Default Move threshold
|
|
- Default Still threshold
|
|
* - 0
|
|
- 50
|
|
- 0
|
|
* - 1
|
|
- 50
|
|
- 0
|
|
* - 2
|
|
- 40
|
|
- 40
|
|
* - 3
|
|
- 30
|
|
- 40
|
|
* - 4
|
|
- 20
|
|
- 30
|
|
* - 5
|
|
- 15
|
|
- 30
|
|
* - 6
|
|
- 15
|
|
- 20
|
|
* - 7
|
|
- 15
|
|
- 20
|
|
* - 8
|
|
- 15
|
|
- 20
|
|
|
|
Button
|
|
------
|
|
|
|
The ``ld2410`` button allows you to perform actions on your :doc:`ld2410`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
button:
|
|
- platform: ld2410
|
|
factory_reset:
|
|
name: "factory reset"
|
|
restart:
|
|
name: "restart"
|
|
query_params:
|
|
name: query params
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **factory_reset** (*Optional*): This command is used to restore all configuration values to their original values.
|
|
All options from :ref:`Button <config-button>`.
|
|
- **restart** (*Optional*): Restart the device.
|
|
All options from :ref:`Button <config-button>`.
|
|
- **query_params** (*Optional*): Refresh all sensors values of the device.
|
|
All options from :ref:`Button <config-button>`.
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
Text Sensor
|
|
-----------
|
|
|
|
The ``ld2410`` text sensor allows you to get information about your :doc:`ld2410`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
text_sensor:
|
|
- platform: ld2410
|
|
version:
|
|
name: "firmware version"
|
|
mac_address:
|
|
name: "mac address"
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **version** (*Optional*): The firmware version.
|
|
All options from :ref:`Text Sensor <config-text_sensor>`.
|
|
- **mac_address** (*Optional*): The bluetooth mac address. Will be set to ``unknown`` when bluetooth is off.
|
|
All options from :ref:`Text Sensor <config-text_sensor>`.
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
Select
|
|
-----------
|
|
|
|
The ``ld2410`` select allows you to control your :doc:`ld2410`.
|
|
|
|
.. code-block:: yaml
|
|
|
|
select:
|
|
- platform: ld2410
|
|
distance_resolution:
|
|
name: "distance resolution"
|
|
baud_rate:
|
|
name: "baud rate"
|
|
light_function:
|
|
name: light function
|
|
out_pin_level:
|
|
name: out pin level
|
|
|
|
.. _ld2410-light-function:
|
|
|
|
Configuration variables:
|
|
************************
|
|
|
|
- **distance_resolution** (*Optional*): Control the gates distance resolution. Can be ``0.75m`` or ``0.2m``. Defaults to ``0.75m``.
|
|
All options from :ref:`Select <config-select>`.
|
|
- **baud_rate** (*Optional*): Control the serial port baud rate. Defaults to ``256000``.
|
|
Once changed, all sensors will stop working until a fresh install with an updated :ref:`UART Component <uart>` configuration.
|
|
All options from :ref:`Select <config-select>`.
|
|
- **light_function** (*Optional*): If set, will affect the OUT pin value, based on :ref:`light threshold<ld2410-light-threshold>`. Can be ``off``, ``low`` or ``above``. Defaults to ``off``.
|
|
All options from :ref:`Select <config-select>`.
|
|
- **out_pin_level** (*Optional*): Control OUT pin ``away`` value. Can be ``low`` or ``high``. Defaults to ``low``.
|
|
All options from :ref:`Select <config-select>`.
|
|
- **ld2410_id** (*Optional*, :ref:`config-id`): Manually specify the ID for the :doc:`ld2410` component if you are using multiple components.
|
|
|
|
Automations
|
|
-----------
|
|
|
|
``bluetooth_password.set`` Action
|
|
*********************************
|
|
|
|
This is an :ref:`Action <config-action>` for setting the bluetooth password.
|
|
|
|
.. code-block:: yaml
|
|
|
|
- bluetooth_password.set:
|
|
id: my_ld2410
|
|
password: "HiLink"
|
|
|
|
Configuration variables:
|
|
|
|
- **id** (**Required**, :ref:`config-id`): The ID of the :doc:`ld2410` component to set.
|
|
- **password** (**Required**, string, :ref:`templatable <config-templatable>`):
|
|
The password to set. Case sensitive. Must be exactly 6 characters long. Default password is ``HiLink``.
|
|
|
|
To change the password from HA you can use the following example config:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ld2410:
|
|
id: my_ld2410
|
|
|
|
api:
|
|
actions:
|
|
- action: set_ld2410_bluetooth_password
|
|
variables:
|
|
password: string
|
|
then:
|
|
- bluetooth_password.set:
|
|
id: my_ld2410
|
|
password: !lambda 'return password;'
|
|
|
|
OUT pin
|
|
-------
|
|
|
|
In order to monitor the presence indicated by the component, with the :ref:`light function<ld2410-light-function>` taken
|
|
under account, you can set up a :ref:`GPIO Binary Sensor <gpio-binary-sensor>`:
|
|
|
|
.. code-block:: yaml
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin: GPIOXX
|
|
name: gpio out pin presence
|
|
device_class: presence
|
|
|
|
|
|
Calibration Process
|
|
-------------------
|
|
|
|
In order to calibrate your ``ld2410`` sensor perform the following:
|
|
|
|
1. Enable :ref:`engineering mode<ld2410-engineering-mode>`.
|
|
2. Monitor the ``gX_move_energy`` and ``gX_still_energy`` :ref:`sensors<ld2410-sensors>`.
|
|
3. Change the :ref:`thresholds<ld2410-number>` and repeat step 2 until satisfaction.
|
|
4. Disable :ref:`engineering mode<ld2410-engineering-mode>`.
|
|
|
|
Home Assistant Card
|
|
*******************
|
|
|
|
For easy calibration process, you can use the following custom manual card.
|
|
|
|
.. code-block:: yaml
|
|
|
|
type: vertical-stack
|
|
title: 'DEVICE'
|
|
cards:
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entities
|
|
entities:
|
|
- entity: 'switch.DEVICE_engineering_mode'
|
|
name: engineering mode
|
|
- type: vertical-stack
|
|
cards:
|
|
- type: entities
|
|
entities:
|
|
- entity: 'number.DEVICE_timeout'
|
|
name: timeout
|
|
- entity: 'number.DEVICE_max_move_distance_gate'
|
|
name: max move distance gate
|
|
- entity: 'number.DEVICE_max_still_distance_gate'
|
|
name: max still distance gate
|
|
- entity: 'select.DEVICE_light_function'
|
|
name: light function
|
|
- entity: 'number.DEVICE_light_threshold'
|
|
name: light threshold
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_detection_distance'
|
|
name: distance
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_moving_distance'
|
|
name: move
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_still_distance'
|
|
name: still
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_move_energy'
|
|
name: move energy
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_still_energy'
|
|
name: still energy
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'binary_sensor.DEVICE_gpio_out_pin_presence_status'
|
|
name: gpio presence
|
|
state_color: true
|
|
- type: entity
|
|
entity: 'binary_sensor.DEVICE_presence'
|
|
name: presence
|
|
state_color: true
|
|
- type: entity
|
|
entity: 'binary_sensor.DEVICE_moving_target'
|
|
name: movement
|
|
state_color: true
|
|
- type: entity
|
|
entity: 'binary_sensor.DEVICE_still_target'
|
|
name: still
|
|
state_color: true
|
|
- type: conditional
|
|
conditions:
|
|
- entity: 'switch.DEVICE_engineering_mode'
|
|
state: 'on'
|
|
card:
|
|
type: vertical-stack
|
|
cards:
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_light'
|
|
name: light
|
|
- type: entity
|
|
entity: 'binary_sensor.DEVICE_out_pin_presence_status'
|
|
name: out pin presence
|
|
state_color: true
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g0_move_energy'
|
|
name: 'g0'
|
|
- type: entity
|
|
entity: 'number.DEVICE_g0_move_threshold'
|
|
name: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g0_still_energy'
|
|
name: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g0_still_threshold'
|
|
name: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g1_move_energy'
|
|
name: 'g1'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g1_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g1_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g1_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g2_move_energy'
|
|
name: 'g2'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g2_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g2_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g2_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g3_move_energy'
|
|
name: 'g3'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g3_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g3_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g3_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g4_move_energy'
|
|
name: 'g4'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g4_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g4_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g4_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g5_move_energy'
|
|
name: 'g5'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g5_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g5_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g5_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g6_move_energy'
|
|
name: 'g6'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g6_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g6_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g6_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g7_move_energy'
|
|
name: 'g7'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g7_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g7_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g7_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: horizontal-stack
|
|
cards:
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g8_move_energy'
|
|
name: 'g8'
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g8_move_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'sensor.DEVICE_g8_still_energy'
|
|
name: ' '
|
|
icon: ' '
|
|
- type: entity
|
|
entity: 'number.DEVICE_g8_still_threshold'
|
|
name: ' '
|
|
icon: ' '
|
|
|
|
Then replace all instances of ``DEVICE`` with your device name
|
|
|
|
The result:
|
|
|
|
.. figure:: images/ld2410-card.png
|
|
:align: center
|
|
|
|
See Also
|
|
--------
|
|
|
|
- `Official Datasheet and user manuals <https://drive.google.com/drive/folders/1p4dhbEJA3YubyIjIIC7wwVsSo8x29Fq->`_
|
|
- `Source of inspiration for implementation <https://github.com/rain931215/ESPHome-LD2410>`_
|
|
- :apiref:`ld2410/ld2410.h`
|
|
- :ghedit:`Edit`
|