80 lines
2.7 KiB
ReStructuredText
80 lines
2.7 KiB
ReStructuredText
ZyAura CO2 & Temperature & Humidity Sensor
|
|
==========================================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up ZyAura co2, temperature and humidity monitors.
|
|
:image: zgm053.jpg
|
|
:keywords: CO2, MT8057, MT8057S, MT8060, ZGm05, ZGm053U, ZG1683R, ZG1583RUD
|
|
|
|
The ZyAura CO2 & Temperature & Humidity sensor allows you to use your
|
|
`ZGm05(3)(U) <http://www.zyaura.com/products/ZGm05.asp>`__
|
|
(`MT8057 <https://masterkit.ru/shop/1266110>`__, `MT8057S <https://medgadgets.ru/shop/kit-mt8057.html>`__),
|
|
`ZG1683R(U) <http://www.zyaura.com/products/ZG1683R.asp>`__ (`MT8060 <https://masterkit.ru/shop/1921398>`__),
|
|
`ZG1583RUD <http://www.zyaura.com/products/ZG1583RUD.asp>`__
|
|
monitors with ESPHome.
|
|
|
|
.. figure:: images/zgm053-full.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
ZyAura ZGm053U CO2 & Temperature Monitor.
|
|
|
|
.. figure:: images/zgm053-connection.jpg
|
|
:align: center
|
|
:width: 80.0%
|
|
|
|
ZyAura ZGm053U connection diagram (1 - empty, 2 - clock, 3 - data, 4 - GND). In some other models the clock and data pins are swapped.
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
sensor:
|
|
- platform: zyaura
|
|
clock_pin: D1
|
|
data_pin: D2
|
|
co2:
|
|
name: "ZyAura CO2"
|
|
temperature:
|
|
name: "ZyAura Temperature"
|
|
humidity:
|
|
name: "ZyAura Humidity"
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **clock_pin** (**Required**, :ref:`config-pin`): The pin where the clock bus is connected.
|
|
- **data_pin** (**Required**, :ref:`config-pin`): The pin where the data bus is connected.
|
|
- **co2** (*Optional*): The information for the CO2 sensor.
|
|
|
|
- All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **temperature** (*Optional*): The information for the temperature sensor.
|
|
|
|
- All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **humidity** (*Optional*): The information for the humidity sensor
|
|
|
|
- All options from :ref:`Sensor <config-sensor>`.
|
|
|
|
- **update_interval** (*Optional*, :ref:`config-time`): The interval to check the
|
|
sensor. Defaults to ``60s``.
|
|
|
|
|
|
.. note::
|
|
|
|
ZGm05 monitor (and maybe others) needs some initial time to get correct data when powered
|
|
on. Only after this timespan will the sensor report correct values. It's not recommended to set
|
|
``update_interval`` lower than ``20s``.
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :ref:`sensor-filters`
|
|
- :doc:`absolute_humidity`
|
|
- :doc:`mhz19`
|
|
- `CO2mon-esp firmware <https://github.com/Anonym-tsk/co2mon-esp>`__ by `@anonym-tsk <https://github.com/Anonym-tsk>`__
|
|
- `Some information about hacking MT8060 <https://habr.com/ru/company/dadget/blog/394333/>`__
|
|
- `CO2MeterHacking project <https://revspace.nl/CO2MeterHacking>`__
|
|
- :apiref:`zyaura/zyaura.h`
|
|
- :ghedit:`Edit`
|