119 lines
5.5 KiB
XML
119 lines
5.5 KiB
XML
<?xml version="1.0" encoding="utf-8"?>
|
|
<Product xmlns='http://code.google.com/p/open-zwave/'>
|
|
<!-- Configuration Parameters -->
|
|
<CommandClass id="112">
|
|
<Value type="byte" index="1" genre="config" label="Sensitivity" units="" min="0" max="255" value="200">
|
|
<Help>
|
|
Sensitivity sets the amount of motion required for the device to
|
|
detect motion. A higher value makes it more sensitive and a
|
|
lower value makes it less sensitive. Note that values above 200
|
|
are not recommended when the device is battery operated.
|
|
Recommended values:
|
|
10 = Pet Immune.
|
|
100 = Medium sensitivity for hallways.
|
|
200(default) = Highly sensitive for rooms where people are sitting still.
|
|
</Help>
|
|
</Value>
|
|
<Value type="byte" index="2" genre="config" label="On Time" units="minutes" min="0" max="255" value="20">
|
|
<Help>
|
|
On Time sets the number of minutes that the lights stay on when
|
|
motion has not been detected.
|
|
A value of 0 On Time is a special mode where the lights are
|
|
constantly sent a command to turn them on whenever motion is
|
|
detected. The device will NOT turn the lights off in this mode.
|
|
Note that this mode will significantly shorten battery life.
|
|
Recommended values:
|
|
5 min for hallways.
|
|
20 min for an office environment.
|
|
60 min for a library or other room where someone may be sitting
|
|
still for a long time.
|
|
This may be inaccurate, but default for Homeseer HSM100 may actually be 3 minutes, instead of 20?
|
|
</Help>
|
|
</Value>
|
|
<Value type="list" index="3" genre="config" label="LED ON/OFF" units="" min="" max="" size="1" value="255">
|
|
<Help>
|
|
LED ON/OFF turns the LED on or off. A slight improvement in
|
|
battery life is obtained by turning the LED off. Setting LED
|
|
ON/OFF to zero will turn the LED off and 255 turns it on.
|
|
Default is On (255).
|
|
</Help>
|
|
<Item label="Off" value="0"/>
|
|
<Item label="On" value="255"/>
|
|
</Value>
|
|
<Value type="byte" index="4" genre="config" label="Light Threshold" units="%" min="0" max="100" value="100">
|
|
<Help>
|
|
Light Threshold is the percentage of light in the room above
|
|
which the lights will not be turned on. Light Threshold is often
|
|
used in room with a lot of natural daylight. Setting Light
|
|
Threshold to a value of 50% will cause the device to not turn the
|
|
lights on when the natural light in the room is already at the 50%
|
|
value. This feature only prevents the lights from coming on when
|
|
motion is first detected and the light level in the room is already
|
|
above Light Threshold. It will not turn the lights off when the
|
|
amount of natural light in the room increases. It will
|
|
automatically turn on the lights in a room that has motion in it
|
|
and that the amount of natural light has dropped below Light
|
|
Threshold.
|
|
A value of 100% turns off this feature (default).
|
|
Recommended values:
|
|
Usually a value between 40% and 60% will prevent the lights
|
|
from coming on in a reasonably well light room and will turn
|
|
them on as it is getting dark. Some experimentation is required
|
|
with each room to determine the proper setting.
|
|
</Help>
|
|
</Value>
|
|
<Value type="byte" index="5" genre="config" label="Stay Awake" units="" min="0" max="255" value="0">
|
|
<Help>
|
|
Setting Stay Awake to a non-zero value will cause the device to
|
|
always be awake. NOTE: this mode should NOT be used when
|
|
the device is battery powered! Batteries will only last a few days
|
|
in this mode.
|
|
Stay Awake is NOT set to the factory default (0) when the device
|
|
is Excluded (reset) from the Z-Wave network.
|
|
Setting Stay Awake to a non-zero value will cause the Z-Wave
|
|
Listening Bit to be set. The device will become a routing node in
|
|
the Z-Wave Mesh-Network when the Listening Bit is set.
|
|
To properly have the device included in the routing tables, set
|
|
Stay Awake to a non-zero value, then reset the device (Exclude
|
|
from the network), then add it back to the network. The new
|
|
routing information will be used now that the listening bit is set.
|
|
Defaults to 0.
|
|
</Help>
|
|
</Value>
|
|
<Value type="byte" index="6" genre="config" label="On Value" units="" min="0" max="255" value="255">
|
|
<Help>
|
|
On Value is the value sent by the Z-Wave BASIC_SET
|
|
command when motion is detected.
|
|
A value of 0 will turn the lights off (not recommended).
|
|
A value between 1 and 100 will set the dim level to between 1%
|
|
and 100%.
|
|
A value of 255 will turn the light on (default).
|
|
NB! According to the manual, the value should not be set between 101-254 (inclusive).
|
|
</Help>
|
|
</Value>
|
|
<Value type="byte" index="7" genre="config" label="TempAdj" units="" min="0" max="255" value="0">
|
|
<Help>
|
|
TempAdj is a twos-complement number that is used to adjust the temperature reading to make it more accurate.
|
|
The value programmed is in tenths of degree Fahrenheit.
|
|
The temperature reading can be adjusted up to +12.7F to -12.8F.
|
|
A value of 1 will adjust the temperature reading by +0.1F.
|
|
A value of -1 will adjust the temperature by -0.1F.
|
|
A value of 123 will adjust the temperature by +12.3F.
|
|
TempAdj is NOT changed when Excluded (reset) from the Z- Wave network.
|
|
</Help>
|
|
</Value>
|
|
|
|
</CommandClass>
|
|
|
|
<!-- add Basic set CC to raise a node_event -->
|
|
<CommandClass id="32" action="add" />
|
|
<!-- map endpoints -->
|
|
<CommandClass id="96" mapping="endpoints" />
|
|
<!-- Association Groups -->
|
|
<CommandClass id="133">
|
|
<Associations num_groups="1">
|
|
<Group index="1" max_associations="4" label="Motion"/>
|
|
</Associations>
|
|
</CommandClass>
|
|
</Product>
|