90 lines
5.7 KiB
XML
90 lines
5.7 KiB
XML
<?xml version="1.0" encoding="utf-8"?>
|
|
<Product xmlns='http://code.google.com/p/open-zwave/'>
|
|
<!--
|
|
Shenzhen NEO Electronics (Neo-CoolCam) Smart Power Plug EU
|
|
-->
|
|
<!-- Configuration Parameters -->
|
|
<CommandClass id="112">
|
|
<Value type="list" genre="config" instance="1" index="1" label="Remember Relay ON/OFF status" value="1" size="1">
|
|
<Help>
|
|
This parameter defined the relay status if remember or not.
|
|
If remembered, the plug will restore the relay status last power off when the plug supply power next time.
|
|
</Help>
|
|
<Item label="Disable" value="0"/>
|
|
<Item label="Enable" value="1"/>
|
|
</Value>
|
|
<Value type="list" genre="config" instance="1" index="2" label="Button On/Off" value="1" size="1">
|
|
<Help>
|
|
This parameter defines the button on/off function is enabled or not on the top of the wall plug.
|
|
If enabled, users can turn on and off the wall plug by pressing the button on the top of the wall plug.
|
|
If disabled, the wall plug cannot be turned on and off by pressing the button.
|
|
</Help>
|
|
<Item label="Disable" value="0"/>
|
|
<Item label="Enable" value="1"/>
|
|
</Value>
|
|
<Value type="list" genre="config" instance="1" index="3" label="Led Display" value="1" size="1">
|
|
<Help>
|
|
This parameter defines the LED indication Function ON/OFF.
|
|
If disabled, then LED indication Function and will always be turn-off, while enabled means LED Function is on.
|
|
</Help>
|
|
<Item label="Disable" value="0"/>
|
|
<Item label="Enable" value="1"/>
|
|
</Value>
|
|
<Value type="list" genre="config" instance="1" index="4" label="Configure Plug Time switch Function" value="0" size="1">
|
|
<Help>
|
|
This parameter defines the timer function Enable/Disable.
|
|
If disabled, then time switch function is not available.
|
|
The time period will be defined in parameter #5.
|
|
If enabled, and when turn the plug relay on, the timer in plug start run with time period defined in parameter #5 and the plug will turn the relay off.
|
|
</Help>
|
|
<Item label="Disable" value="0"/>
|
|
<Item label="Enable" value="1"/>
|
|
</Value>
|
|
<Value type="short" genre="config" instance="1" index="5" label="Configure Time switch Period" units="minute" value="120" min="0" max="32767" size="2">
|
|
<Help>
|
|
This parameter defines the time period that plug time switch off. This parameter can be configured 0 - 32767(in minutes).
|
|
If Parameter #4 is enabled, and relay is turn-on, the relay will be turn-off after delay this parameter.
|
|
</Help>
|
|
</Value>
|
|
<Value type="list" genre="config" instance="1" index="6" label="Send Meter Report" value="1" size="1">
|
|
<Help>
|
|
This parameter defines Disable/Enable meter report measure data to controller.
|
|
When device is detected an OCP event or the relay turned on or turned off, device still will report all meter values once if this configuration is disabled.
|
|
</Help>
|
|
<Item label="Disable" value="0"/>
|
|
<Item label="Enable" value="1"/>
|
|
</Value>
|
|
<Value type="short" genre="config" instance="1" index="7" label="Meter Report Interval" units="second" value="300" min="30" max="32767" size="2">
|
|
<Help>This parameter defines interval time (30-32767 seconds) that Meter report data to main controller .</Help>
|
|
</Value>
|
|
<Value type="byte" genre="config" instance="1" index="8" label="Configure maximum over-load current" units="Ampere" value="16" min="1" max="16" size="1">
|
|
<Help>
|
|
This parameter defines maximum current (in Amperes) the plug can provide to load that be connected to plug.
|
|
If the current consumed by load is greater than maximum current, the plug will cut off power, and send NOTIFICATION_EVENT_POWER_MANAGEMENT_OVER_LOAD_DETECTED to associated devices in lifeline. Red Led will blink every seconds until current is normal (less than Parameter #8).
|
|
You must remove the loader and turn on the Plug (press the button once) to enable current monitor and clear NOTIFICATION ALARM. This parameter value must be great than #10.
|
|
If user set this parameter to default by Configure CC, the parameter #10 will be set to default value.
|
|
</Help>
|
|
</Value>
|
|
<Value type="short" genre="config" instance="1" index="9" label="Configure power report" units="cA" value="50" min="1" max="1600" size="2">
|
|
<Help>
|
|
This parameter defines by how much power consumed must change to be reported to the Z-Wave Controller or Z-Wave Gateway, in centiAmperes (1-1600). If the rate of power consumed change ratio is greater than this parameter, the plug will report the results, voltage, current, power and energy, that plug measure to Z-Wave Controller or Z-Wave Gateway
|
|
The changed value = [Value] x 0.01A
|
|
</Help>
|
|
</Value>
|
|
<Value type="byte" genre="config" instance="1" index="10" label="Configure maximum Alarm current" units="Ampere" value="13" min="1" max="16" size="1">
|
|
<Help>
|
|
This parameter defines maximum current (in Amperes), if the current plug provide to load is greater than this parameter, the plug will send over-current notification to the controller and the LED will turn RED, but plug cannot cut-off power. This parameter value must be less than parameter #8.
|
|
If user set this parameter to default by Configure CC, the parameter #8 will be set to default value.
|
|
</Help>
|
|
</Value>
|
|
</CommandClass>
|
|
<!-- Association Groups -->
|
|
<CommandClass id="133">
|
|
<Associations num_groups="3">
|
|
<Group index="1" max_associations="5" label="Lifeline"/>
|
|
<Group index="2" max_associations="5" label="Over-load current"/>
|
|
<Group index="3" max_associations="5" label="Send Notification"/>
|
|
</Associations>
|
|
</CommandClass>
|
|
</Product>
|