rtl_433/conf/fan-11t.conf

97 lines
2.3 KiB
Plaintext

#
# FAN-11T Remote Control of Harbor Breeze Fan
#
# KUJCE9103 FAN-11T FAN-53T 2AAZPFAN-53T
#
# written: Peter Shipley
#
# https://www.amazon.com/s?k=Fan-11T
#
# Based on the Holtek the HT12E/HT12F chipsets
#
# HT12E : https://www.holtek.com/documents/10179/116711/2_12ev120.pdf
# HT12F : https://www.holtek.com/documents/10179/116711/2_12dv120.pdf
#
# FCC ID: L3HFAN11T
#
# https://fccid.io/L3HFAN11T
#
# 0.36ms Short
# 0.71ms Long
#
# 12bits of info ( 13 bits transmitted )
#
# receiver requires three matching transmissions optionally followed by one packet with all shorts
#
# The Fan-11T uses a 4 bits dip-switch as an identifier
#
# packets can be described as
#
# <short> <long> + 4 bit ID + <short> + 6 bit command
#
# The follow table uses '1001' as the ID code:
# if short is 0 and Long is 1
#
# Hi 0 1 1 0 0 1 0 1 0 0 0 0 0 = 0110010100000 = 3232 = 0xca0
# Med 0 1 1 0 0 1 0 0 1 0 0 0 0 = 0110010010000 = 3216 = 0xc90
# Low 0 1 1 0 0 1 0 0 0 1 0 0 0 = 0110010001000 = 3208 = 0xc88
# Off 0 1 1 0 0 1 0 0 0 0 0 1 0 = 0110010000010 = 3202 = 0xc82
# Lit 0 1 1 0 0 1 0 0 0 0 0 0 1 = 0110010000001 = 3201 = 0xc81
# End? 0 1 1 0 0 1 0 0 0 0 0 0 0 = 0110010000000 = 3200 = 0xC80
#
#
#
# 0110010000010
# rtl_433 -R 0 -f 302450000 -c fan-11t.conf
# The FCC Documentation list the frequency at 303.9MMz but the devices tests out to between 303.4 and 303.5 (depending on battery)
# To reduce false positives, uncomment the match
# field and set the value to your remote's dip switch pattern
# eg: if your Dip-switch setting is up-down-up=up ( '1011' )
# set the match setting in the decoder definition to 0x6C
# for example:
# match={7}0x66C
#` Dip Switch match preamble
# 0000 0x40
# 0001 0x44
# 0010 0x48
# 0011 0x4C
# 0100 0x50
# 0101 0x54
# 0110 0x58
# 0111 0x5C
# 1000 0x60
# 1001 0x64
# 1010 0x68
# 1011 0x6C
# 1100 0x70
# 1101 0x74
# 1110 0x78
# 1111 0x7C
frequency 302.400M
decoder {
name = Fan-11t,
modulation = OOK_PWM,
short = 360,
long = 710,
gap = 0,
reset = 5000,
tolerance = 50,
unique,
invert,
bits = 13,
get = id:@2:{4},
get = button:@7:{6}:[32:fan_Hi 16:fan_Med 8:fan_Low 2:fan_Off 1:light 0: 4: ],
}